What have you done to your Silverado ZR2 this week? 🛠️

Got it! I think I will get the mat and some locks for the top cubbies.
I got the second gen. Chevy accessories had it for $400 off so I said what the heck, I don't need to eat for 6 mths anyway.
Decked are always about 1500 so that 400 off is an outstanding deal! I've got the Gen 1 so I've got four ammo boxes and I can't lock them but I do have locks on my drawers and drain plugs. Did you know you can turn the drawers into coolers? Pretty neat eh! And just remember their waterproof, but they're not dust proof. I can spray them with my power washer or take him through the car wash and not one drop gets in them but I go on a trail and they end up dusty on the inside.
That's kind of why I got the drain plugs installed so that I can rinse them out easy But I did use it as a cooler one time just past summer and it was pretty awesome
 
Decked are always about 1500 so that 400 off is an outstanding deal! I've got the Gen 1 so I've got four ammo boxes and I can't lock them but I do have locks on my drawers and drain plugs. Did you know you can turn the drawers into coolers? Pretty neat eh! And just remember their waterproof, but they're not dust proof. I can spray them with my power washer or take him through the car wash and not one drop gets in them but I go on a trail and they end up dusty on the inside.
That's kind of why I got the drain plugs installed so that I can rinse them out easy But I did use it as a cooler one time just past summer and it was pretty awesome
Yeah that's pretty cool. I'm still trying to figure out how to sort my stuff. Think I'm going to order more dividers. I didn't think I was going to haul around all that crap but I filled the bins up quick lol.
 
Got my new rig this week! So excited! Came from a ‘22 HD Denali gas job. Time to sell the holiday trailer, so it was time for a fun truck! Not many mods yet, just Expel PPF on hood, fenders, bumper and mirrors, and Truxedo Low Pro tonneau. Get my off road high profile steps next week. Ordered a short radio antenna and stake pocket plugs today. Looking for some lower profile splash guards. Suggestions please!
 

Attachments

  • IMG_6427.webp
    IMG_6427.webp
    466.2 KB · Views: 90
  • IMG_6429.webp
    IMG_6429.webp
    401.8 KB · Views: 86
  • IMG_6363.webp
    IMG_6363.webp
    428.3 KB · Views: 88
  • IMG_6355.webp
    IMG_6355.webp
    361.3 KB · Views: 90
Yeah that's pretty cool. I'm still trying to figure out how to sort my stuff. Think I'm going to order more dividers. I didn't think I was going to haul around all that crap but I filled the bins up quick lol.
Yep! I purchased four extra dividers plus two more boxes, One of the larger ones in one of the smaller ones. I also installed nine extra tie-down points and used a Dremel tool to cut out the areas by the tie down points because they sit level with Decked. I also purchased two locks, one for each drawer and the drain plug kits. You will have to remove each drawer completely and drill the according size hole for the drain plug. It has a threaded rubber grommet which the cap screws into for the drain. I'm sure as you know by now you'll have to remove your fold down assist handle because the Decked won't fit with it. Here's a couple pictures of how I have mine set up.
 

Attachments

  • 20241030_113314.webp
    20241030_113314.webp
    231.8 KB · Views: 77
  • 20241030_113254.webp
    20241030_113254.webp
    273.7 KB · Views: 73
  • 20241030_113244.webp
    20241030_113244.webp
    305.5 KB · Views: 76
I moved my Diode Dynamics SSC1's behind the grill, Added ADD ditch light brackets with Diode Dynamics SSSC2's, Added flush mount Diode Dynamics SSC1's to the rear bumper and added an Auxbeam controller to the console.
 

Attachments

  • ZR2 diodes-01.webp
    ZR2 diodes-01.webp
    567.6 KB · Views: 145
  • ZR2 diodes-02.webp
    ZR2 diodes-02.webp
    471.9 KB · Views: 135
  • ZR2 diodes-03.webp
    ZR2 diodes-03.webp
    395 KB · Views: 139
  • ZR2 diodes-04.webp
    ZR2 diodes-04.webp
    138.1 KB · Views: 143
I moved my Diode Dynamics SSC1's behind the grill, Added ADD ditch light brackets with Diode Dynamics SSSC2's, Added flush mount Diode Dynamics SSC1's to the rear bumper and added an Auxbeam controller to the console.
Can you share some close up “off” pics of how the rear flushes tuned out.
 
Can you share some close up “off” pics of how the rear flushes tuned out.
It’s a little dirty right now but here you go. It was an easy install but if I did it again I would go with the SSC2’s for a little more light output. These are pretty bright though.
 

Attachments

  • IMG_6541.webp
    IMG_6541.webp
    339.9 KB · Views: 72
  • IMG_6540.webp
    IMG_6540.webp
    452.7 KB · Views: 70
Yep! I purchased four extra dividers plus two more boxes, One of the larger ones in one of the smaller ones. I also installed nine extra tie-down points and used a Dremel tool to cut out the areas by the tie down points because they sit level with Decked. I also purchased two locks, one for each drawer and the drain plug kits. You will have to remove each drawer completely and drill the according size hole for the drain plug. It has a threaded rubber grommet which the cap screws into for the drain. I'm sure as you know by now you'll have to remove your fold down assist handle because the Decked won't fit with it. Here's a couple pictures of how I have mine set up.
That's some good info brotha. I won't really miss the grab handle but might make use of the mounting points it left behind for something. I like how you dremmeld that out.
 
Installed a midland mxt575 radio under the passenger seat using the Pinnacle offroad mount. Pretty stoked with the install, however routing through the firewall sucked ass- had to pull a wheel well liner to get to the grommet. Also used a Cali raised ditch light extention to mount the antenna.
1000012071.webp
1000012073.webp
1000012074.webp
1000012075.webp
 
Installed a midland mxt575 radio under the passenger seat using the Pinnacle offroad mount. Pretty stoked with the install, however routing through the firewall sucked ass- had to pull a wheel well liner to get to the grommet. Also used a Cali raised ditch light extention to mount the antenna.View attachment 17514View attachment 17515View attachment 17516View attachment 17517
Just in case you haven’t had an MXT before, make sure you change the setting to use the mic as the speaker instead of the head. (Or set it for both)
 
Wife wanted all black wheels, so i had hers powder coated (little dirty atm, but came out nice). Only had $700 total, powder coat, lugs, center caps and mount and balance. What was cool, a guy not far from me was selling a brand new oem set on marketplace. He loaned me his to get powder coated, then I gave him back hers.
IMG_0736.webp
 
Wife wanted all black wheels, so i had hers powder coated (little dirty atm, but came out nice). Only had $700 total, powder coat, lugs, center caps and mount and balance. What was cool, a guy not far from me was selling a brand new oem set on marketplace. He loaned me his to get powder coated, then I gave him back hers.View attachment 17632
Actually look pretty nice. Maybe I’ll rethink the black lug nuts if I can find them cheaper than $200.
 

Latest Posts

Back
Top