First Silverado ZR2 Mod?

It was. There is some extra work involved in getting the shock clocked right, after installing the spacer. Since I didn't have a spring compressor, I put the top of the shock in a vice and turned the shock inside the coil-over to get them clocked correctly (you have to do this so the reservoirs will be on the back of the shock).
Thanks for the information. Will pass it on. Would be interested in seeing pics with the spacers. I don’t hate the factory rims. Just wanted to see a wider stance and maybe a little bigger tire. Spacers could definitely fit the bill!
 
Just don't do the 22" rims on 35's with a massive nega I've offset. It's literally the worst look of all truck mods.
Lol! Never gonna happen. 22’s are to big in my opinion and I don’t like anything sticking out more than an inch past the Wheelwell.
 
Thanks for the information. Will pass it on. Would be interested in seeing pics with the spacers. I don’t hate the factory rims. Just wanted to see a wider stance and maybe a little bigger tire. Spacers could definitely fit the bill!
 

Attachments

  • 60B30148-0E91-4D04-916A-34D0DBC6A275.jpeg
    60B30148-0E91-4D04-916A-34D0DBC6A275.jpeg
    379.3 KB · Views: 368
2” level and 1.25” wheel spacers. May raise the back of it 1/2”-1”.
 

Attachments

  • 5DFFC065-2522-4CEE-9E51-46A6E09D87F8.jpeg
    5DFFC065-2522-4CEE-9E51-46A6E09D87F8.jpeg
    379.3 KB · Views: 483
  • 4B32CAA6-F604-4A41-9A91-87A8D6D6CBA1.jpeg
    4B32CAA6-F604-4A41-9A91-87A8D6D6CBA1.jpeg
    295.7 KB · Views: 484
  • C06F42DD-7B1A-457A-914E-B42EBC6D2585.jpeg
    C06F42DD-7B1A-457A-914E-B42EBC6D2585.jpeg
    389 KB · Views: 508
That looks great! What kits did you use for the level and spacers?
Spacers were G2 Axle and Gear. You will need to grind about a 1/4" off the wheel studs, so they don't hit the back of wheel.

Leveling kit was a Motofab 2" (part# CH-2).
 
Here the photo of the front sorry for late reply buddy.
 

Attachments

  • 8B11FAE8-C423-4942-A6BD-72670CE5B9C7.png
    8B11FAE8-C423-4942-A6BD-72670CE5B9C7.png
    388.5 KB · Views: 390
  • 1E55F86A-54E2-4A89-8FF1-43E0545047A1.jpeg
    1E55F86A-54E2-4A89-8FF1-43E0545047A1.jpeg
    299 KB · Views: 384
  • 3C96C3C6-280A-40A1-84FB-E34ED6F405D2.png
    3C96C3C6-280A-40A1-84FB-E34ED6F405D2.png
    388.5 KB · Views: 382
A lil trimming left to do.The overall its gonna be about a inch total cut from original. Now got most of hard right rub gone just slight passenger side Rub.
I’ve been lagging honestly should of been done already.
 
Just picked up the truck today. First impressions VERY good! It's everything I thought it was. Have to quickly debadge it and change the exhaust. Way too quiet
 
Ordered Borla exhaust, short antenna, led reverse lights, and black vinyl lettering. Anyone figure out an auto-start delete? Haven't seen anything with the new dash.
 

Most Member Reactions

Back
Top